Showing posts with label work station. Show all posts
Showing posts with label work station. Show all posts

Saturday, February 8, 2014

Compact Bedroom Workstation


Materials: 2 Billy Bookshelves, Norberg Table, Lindmon Tabletop, Vattna Wall Clock, Sultan bed slats, drywall screws, wood screws, washers, latex-based construction caulk, television flush mount, Forstner Drill bit

Description: In need of a 30" desk with ample storage to utilize between our two closets, I racked my brain to find a solution. I toyed with custom-building a cabinet, but finally came upon a good fit with numerous IKEA pieces.

By placing the two Billy Bookshelves back-to-back (leaving a space in between for wiring to pass), I found that the Lindmon tabletop was a perfect spacer. The white melamine makes a clean and light front, too. Weight was important so that the TV (my monitor) would not pull the whole assembly over.

I screwed in from the back, using drywall screws just shorter than the depth of the Billy sideboards and tabletop combined. A bit of caulk helps as a quasi-removable adhesive (installers regularly use this alone to hold countertops in place so why not here?). Disc washers prevented the screws from self-countersinking and ruining the tabletop.



Upon installing the tabletop I immediately installed the TV bracket, also screwing through the tabletop into the Billy sidewalls, using provided bolts to also go into pieces of SULTAN slats in the gap space between the two Billy bookshelves.

This now gave me placement for wire pass-throughs for the Computer, USB and other wires. These were quick and easy in in one Billy back and through the middle of the Lindmon white face with the Forstner bit (cuts a larger circle for easy wiring passthrough).

Now I measured exactly 29.5" - the height of my favorite desk - to help position the Norberg bracket and installed onto the front. Again, each screw was chosen so that depth is just less than the depth of combined tabletop and bookshelf siding. The middle brackets went into the same Sultan slats that are in the gap space behind.

Due to the Norberg gateleg needing stabilization lower down, I placed two Sultan slats together and screwed through to match the Lindmon depth. I will paint this unfinished pine either clean white or black to match the rest of the setup one day soon...

Then I just fed through power cables and monitor wiring, as well as hooking through my speaker cables for my desktop audio system and centered the clock to finish the look!

Now, I have a workstation that easily gets out of the way, and allows me to watch television in the ideal spot in the bedroom, and now my girlfriend and I each have a good stable stack of storage facing our closets to use for whatever we need.

~ Ian C.

Tuesday, June 4, 2013

Wall-mounted charging station plus earphone/cable storage


Materials: Forhoja set of 3 boxes, electric drill with centre bit, wood glue, a few small nails, strip of 4x1 cm wood, extension lead

Description: We have in our household: 2 e-readers, 1 iPad, 1 smaller tablet computer, 1 iPhone, 2 other cell phones and a camera. All of which need to be charged ALL THE TIME. Result: We were constantly looking for charging cables, free wall sockets and the devices themselves.

So I built this charging station which can also be used to stores extra charging cables, earbuds and cell phones. I wanted a wall-mounted station so as not to clutter up the last few precious bits of free table and shelf surface.

I got the Forhoja boxes - it's a set of one big and two smaller boxes; the big one comes with a tray-like lid. The entire thing is just wide and deep enough to comfortably hold the iPad, at least to Kindles and two cell phones at the same time.


First I attached the little pieces of wood into the big box (instead of into the lid as per instructions) to prevent the lid from sliding about.

Using wood glue, I glued the smaller boxes on the sides of the big box. Originally I hadn’t planned to use the small boxes at all, but they make an excellent place to keep earbuds (which disappear all the time as well). I glued 4 strips of wood (10 x 4 x 1cm) to the back to provide a little space between box and wall and put a few small nails in for extra sturdiness.

I drilled a few 22mm ventilation holes into the lid and the bottom of the big box to prevent the charging plugs and extensions lead from overheating. (Note: don’t forget to put a piece of scrap wood under the box when drilling ventilation holes! You can also put sticky tape on the underside so the wood won’t splinter outwards when the drill breaks through.) I also drilled holes into the back for wall mounting with two screws and washers.

When I screwed the box to the wall I placed the power cable along the back of the box so it runs down the middle between the strips of wood. I had to use a manual screwdriver because the electric screwdriver wouldn’t fit â€" hard work! The cables inside the box are gathered together with a bit of plastic-coated wire so they won’t go all over the place when the lid is lifted off. The lid goes on to the box deep-side up, so the devices can be propped against the wall and won’t slip over the edge.

I'€™m pretty pleased with the whole thing; I only wish I had painted it a bright colour before screwing it to the wall - maybe I'€™ll do that at a later date when I can face having to screw it on again with the tiny manual screwdriver.

~ Nina Hyland, Munich, Germany

Saturday, June 1, 2013

Map It Out Desk


Materials: Vika Moliden underframe

Description: I used the the Vika Moliden under frame aka desk legs. I would of purchased the desk top too but b/c of where I live they wouldn't ship it. So, I had a desk top made with the exact same dimensions of the one you can purchase at Ikea.

I download a picture of the Jackson Hole Mountain Resort Trail Map then imported it into photoshop and changed the dimensions to fit how I wanted it to appear on the desk top. Then, I took the pdf file to a large format printing company who printed it out on sticker paper. Lastly, I carefully placed the giant sticker on the desk and then added a glass top.

It was super easy.

Checkout the link below for the DIY video I did on the process.

See more of the map desk.

~ that girl katie, Jackson Hole, WY

Tuesday, May 28, 2013

Drop Leaf Expedit


Materials: Ikea Expedit, Various sizes

Description: I needed a large workspace with lots of storage in my small studio; and sometimes, I needed to not have such a large workspace in my small studio. After looking a gate leg tables, extendable tables, shelves and every combination thereof, I finally decided to hack an Expedit to fit the bill.

A combination of Expedit units, a luan bifold door, and some drop leaf table hardware made for the exact unit I needed, both when I need space and when I don'€™t. Just lift the tabletop, slide out the latch, and I have a 36"€ x 78"€ workspace. Slide the latches back in, and I have a 18"€x78" inch wall storage unit.



Supplies
Expedit Units:
1-1x5 (I left out one shelf to accommodate a small flat screen tv)
2-2x2
2-1x2 (I originally planned to mix and match a 2x2 and 1x1 to create these, but when I got to Ikea, they already had the 1x2's available)

Expedit Inserts, as desired- I used one drawer unit and one door unit.

1 36 x 78 inch luan Bifold door (hinges already attached, stained or painted to match Expedit)

2 pairs of sliding drop leaf table hardware

Directions:
Assemble Expedit, stain bifold door if necessary.

Line up 2x2 units, side by side, (If hacking by yourself, turn them perpendicular to wall to hold the tabletop while you work.) Lay the bifold door flat over the units.

Stack 1x2 units on top outside edges of bifold door, then stack 1x5 unit horizontally over top of 1x2 units. Adjust units so everything is centered.

Mark the latch placement for 2 outside drop leaf latches on the outside edges of the bifold door on the underside. Make sure you attach close to the edge so your screws bite into the framing wood of the door, under the surface. Attach. I used longer wood screws than were provided, just to get a good anchor.

(If you turned the 2x2s to hold the door, un-stack entire unit. Turn 2x2'€™s parallel with wall, leaving space between. make sure they line up inside the hardware already attached.)

Attach 2 drop leaf latches in the center space, as far apart a you are able.

Re-stack entire unit. Add boxes for storage as desired.

I did not attach my pieces together, because they need to be movable, but joining brackets on the back are probably a good idea for permanent installation.

~ Diann Liptak, Richmond, Virginia, USA

Wednesday, May 22, 2013

Modern dry-erase standing desk


Materials: Linnmon high-gloss white tabletop (59x29½); Expedit 4x2 shelving unit; 2 Expedit drawer inserts, high-gloss white; 2 Expedit door inserts; 12 Capita legs; Lack shelf, high gloss red (43¼x10¼)

Description: My wife and I have wanted to put together a standing desk for a long time, and took our recent move as an opportunity to finally do it. After spending a lot of time on Ikea Hackers and ikea.ca, a couple of visits to Ikea, and several draft designs, we've ended up with this, and we think it's pretty awesome. Our favorite part is that the desk itself functions as a white-board.

When designing yours, you'll want to keep in mind the target height of your desk, and account for it by varying the legs you use. Ikea offers the Capita legs in 3 different heights, so by combining them you should be able to get pretty close to your desired height. In our case, I'm about 5'11" and my wife's probably 5'3" or 5'4". Accounting for the thickness of the tabletop itself, our final desk height is 41", which is pretty comfortable for both of us.



Ingredients:
- Linnmon high-gloss white tabletop (59x29½): $39.00
- Expedit 4x2 shelving unit (approximately 31x15½ x58½ ): $79.00
- 2 Expedit drawer inserts, high-gloss white: 2 x $25.00
- 2 Expedit door inserts (high-gloss red & high-gloss white): 2 x $15.00
- 12 Capita legs (4¾”): 3 x $16.99
- Lack shelf, high gloss red (43¼x10¼): $24.99

Recipe:
- Build the Expedit, in our case leaving out one of the smaller shelves to make room for the computer.
> NOTE: Looking at the Expedit in the horizontal position, the vertical separators are indispensable. In my opinion, you would be ill-advised to leave out any of those, as they provide structural support.
- Drill 6 Capita legs into the bottom of the Expedit. The Expedit seemed to be made of solid wood, so a drill was necessary but the capita legs feel nice and stable.
> Ikea makes a caster set designed specifically to support the Expedit in its horizontal position, and they use 6 casters, including 1 pair to support the middle of the unit. Based on that, I decided to use 6 Capita legs, including 2 for support in the middle.
- Break out the Linnmon tabletop, and line it up on top of the Expedit. Figure out where the Expedit will be below it, and mark the widest (most stable) possible locations for the other 5 (yes 5) Capita legs.
> Given that there wouldn'€™t be much weight on the desktop and that I wanted to use the space between the Expedit and Linnmon for storage of stuff, I decided not to use a Capital in the middle in front. You can sort of see in one of the photos what I mean: There are 3 legs along the back of the tabletop, but only 2 in front.
> When you'€™re thinking about how you want to position everything, keep in mind that the further back you set the Expedit under the Linnmon, the harder it'll be to get at those drawers. We set the Expedit about 4” back under the tabletop.
- Drill holes for the capita legs in the Linnmon, and screw them in. Note that the edges of the Linnmon are solid wood, so the outside 4 legs are good. But the center of the desktop is fibreboard, or hollow filled, or whatever, so be gentle with that center Capita. It'€™s only there to provide support, and you'€™re only drilling it in to prevent it from sliding around.
- Now figure out how high you want your monitors. "€œErgonomics" says that the top of the monitor should be right around eye level when looking straight forward.
- If you'€™re going to use the lack shelf to support your monitors, FIND STUDS IN YOUR WALL. If you screw the shelf into drywall or particle board and put two monitors on it (possibly even one monitor), it's liable to just rip right out of the wall, wrecking everything from your wall to the Expedit below, including your monitor. If you don’t know how to find studs or aren't comfortable, you have lots of other options: prop the monitors up on books; get another piece from Ikea (we considered the Alex Alex shelf with drawer) that you can just sit on the desktop), get a monitor riser from another shop.
> Quick note: If you're going to rest your monitors directly on the desktop, they'€™re going to add a lot of weight to the back of the desktop, and depending on how you'€™ve placed your Linnmon on top of the Expedit, it may not have a lot of support at the back. If this is the case, the monitors might be heavy enough to flip the desktop up. You can address this in a number of ways, but one option is the Vika Byske legs which extend tall enough to provide support at the back of the tabletop. Even one in the center of the table would probably be enough.
- There you have it. Load in the drawers and doors (if you'€™re using them), connect everything, and you'€™re good to go.

~ Liohn Sherer, Montreal, QC, Canada

Thursday, May 16, 2013

Compact living desk mod


Materials: Variera kitchen shelf insert, Capita legs and Ekby shelf

Description: Not much of a hack if you compare to some of the other things posted here and part of it has been posted plenty of times.

I live in a small room in London and wanted to make use of the desk space more efficiently.

I put my monitor and speakers on the standard Ekby shelf on Capita legs hack that have been posted here plenty of times before.

What I haven't seen here before though is the Variera Kitchen Shelf Insert.

I mounted it upside down under the desk to keep my Xbox of the floor without taking up space on the desk.

Quite an easy hack but made a huge difference in my room.

Let me know what you think!

~ Jonas, London