Showing posts with label storage. Show all posts
Showing posts with label storage. Show all posts

Monday, June 3, 2013

Non-flimsy full height, 24" wide recycling and trash cabinet


Materials: Akurum kitchen cabinet, drawers, jigsaw, drill.

Description: Ikea's kitchen cabinets are great, but their recycling center is limited to an 18" wide cabinet with a drawer above. That's not tall enough and if you use a full height door, when you pull the handle, the whole door flexes outward. And at 18" wide it's just not big enough for a family's trash and recycling.

SOLUTION: Use a 24" wide cabinet with full height door panel and an extra drawer kit. Don't buy the Ikea recycling kit, use standard Sterilite laundry bins instead.

1. Attach your bottom drawer to the door panel per the instructions and template and your rails into the cabinet. You can now install the assembly into the cabinet and it will slide in and out.



2. Stand your bins sideways (see photos) so there is an even gap to the front panel, back of drawer and between the two bins. This will allow enough wood when we come to cut the upper drawer base.

3. Offset the bins sideways, which when finished will allow for a roll of trash bags to sit in the bottom.

4. Assemble your second drawer without the base / floor in it. With your door open and the bins in place, hold the drawer (maybe need a friend for this) around where you plan to install it to determine which holes your rails should go in. Mark inside the cabinet, install your rails and fit the drawer without the base in it. The drawer should slide in and out.

5. Slide the upper drawer forward until it hits the cabinet front and mark where you will attach it to the door / front. This is a little tricky and is best done with the door as closed as possible so the drawer is sitting rigidly in the rails and not drooping down at full extension.

6. Re-use the Ikea template from step one to finalize your drawer attachment points on the door. Drill the holes and attach the drawer to the door front and check the operation. Your drawer base will still be missing.

7. Mark a line from the bottom of the upper drawer onto one bin. This is the level that the bin passes through the drawer base. Measure the depth and width of each bin and draw the outline on your drawer base. If in doubt make it a little small at first as the wood is easy to enlarge with a rasp. Cut your holes with a jigsaw.

8. Detach the upper drawer from the door and slide in the drawer base. You may need to remove the door completely first to get the board to slide in. Reattach everything.

The bins should drop into your two holes in the upper drawer base. If the bins don't sit all the way in the bottom drawer, your holes may be too small. Enlarge them a little with a rasp.

~ Patrick Ryan, San Diego

Friday, May 24, 2013

Clipshelf - The shelf parasite


Materials: Powdercoated steel sheet

Description: This small add-on for standard shelves makes a designer item out of each ordinary IKEA Billy (Udden, Besta or similar products with a standard row of holes with 32mm distance)

Clipshelf adds additional space on existing bookshelves or gives your favourite books an extra place. Fits also to kitchen cabinets or bathroom furniture.


Vote for clipshelf here to make a good idea become real: The Italian design label ex.t will produce the winner of this contest...

Design: !idee / Michael Hilgers

See more of the Clipshelf.

~ Michael Hilgers, Berlin

Friday, May 10, 2013

Pretty Jewelry Holder from Wooden Cutlery Tray


Materials: Wooden Cutlery Tray, Paint, Glass Knobs, Cup Hooks

Description: Sand the tray thoroughly and paint all sides and crevices carefully with a brush (I used Valspar's Tempered Gray for my main colour).

Let the coat dry, and then paint another coat.

I chose to add some hand painted details inside the boxes of the tray with white paint (Valspar'€™s Ultra White) and one of my daughter'€™s little craft brushes, but you could also skip this step or try painting with a stencil (or painting the back panels a different solid colour). The options are endless!



Add a coat of clear varnish.

Next, attach the knobs to the tops of each compartment. I used super glue instead of a drill - it was a lot easier and it seems to be holding well!

Screw the little cup hooks along the bottom of the tray (I used 5).

See more of the jewelry holder from cutlery tray.

~ Christina Dennis, Stony Plain, Alberta, Canada