Materials: 8" and 5" Blanda Matt Bowls, Tolsby picture frame base, 4 disposable wooden chopsticks (preferable the round kind), foam board
Description: To make the chair:
Step 1: Take the round base of the Tolsby picture frame and position the 8" Blanda Matt Bowl on its side at an approximate 75degree angle on top of the white base.
Step 2: Make a mark on where the white base will be glued to the bowl.
Step 3: Use hot glue to stick the base.
*Make a cushion for the chair if you want.
To make the table:
Step 1: cut a 10.5dia circle from the foam board. Glue it inside the 5" Blanda Matt bowl.
*Cover the foam board with decorative paper if you want. I used a silver contact paper.
Step 2: measure 1" from the tapered tip of all 4 chopsticks. Cut and superglue them at the bottom of the 5" bowl for table legs. I have mine spaced around 1" away from the IKEA logo at the bottom of the bowl.
~ Lene Dragon, United States
Materials: Fyndig - single-bowl sink (17 3/4" x 15 3/8") plus Atlant Waste Strainer, Edsvik, dual control faucet, Bohlman Dish Washing Bowl and Drainer, Rationell fully-extending drawers, one 3" and one 6" deep Jall- Hanging organizer.
Description: In 2012, I purchased a small 1986 mini motorhome that was in need of interior renovation---especially the kitchen area. After looking around, I found IKEA products were better sized for the mini motorhome than products at many other stores. I was excited to find how well the IKEA products worked and hope this gives others ideas for using IKEA products to renovate their van or mini-motorhome.
The first step was to remove the old stove, sink, faucet and the countertop. The original cabinet frame was repaired and reinforced. The old frame was covered with a new 1/4-inch plywood skin and a new countertop was added.
Then I installed the new IKEA sink and faucet. Note: plumbing lines on motorhomes are sized differently than for houses. The sales people at a local hardware store helped me find parts that could be used to connect the new sink lines to the original motorhome water lines. We used couplers for a sprinkler system.
Below the new cooktop, I installed full extension Rationell drawers. These are wonderful and easy to use. No more searching through boxes and bags to find items. Note: For the drawers to work properly, the distance between the walls inside the cabinet need to be exactly the dimensions stated on the instructions. In old motorhomes, this is a challenge because cabinets and walls are often not square or straight. We used shims to align the drawer railings.
Several IKEA kitchen accessories have proven to be useful in the motorhome where space is a premium. We LOVE the IKEA espresso maker and covered spice jars. A Bolhmen dish washing basket and drainer set serve double duty. A clean was dish washing basket has served as a salad bowl and the drainer has been used as a colander for rinsing fruits and vegetables and draining pasta.
In addition to rebuilding the kitchen, the clothes closet was a problem. While the closet was large for a minimotorhome, clothes fell off hangers when traveling and had to be stored in bags and boxes so they were hard to get to. The IKEA Jall hanging organizers were just the right length to hang in the closet and they formed cubby holes for storing clothes. I cut 1/4 plywood to fit into the bottom of each cubby hole to add stiffness. Instead of plywood, I could have used foam core board. Now clothes are easy to find and stay in place when traveling.
~ Sue, Western Washington
Materials: HUSET living room scale modified with door hardware.
Description: The HUSET living room playset is slightly undersized for 1:6 scale, but a minor modification using bi-folding door hardware brings it up to snuff so a "little" IKEA design magic can happen.
See more of the HUSET doll furniture hack.
~ Ro
Materials: Finnvar stand
Description: I repurposed the FINNVAR stand and turned it into a height adjustable slider rail for my DSLR camera slider (which I built by cannibalizing my girlfriends roller-skates and spending countless hours at the tool store - but that's a different story).
The concept is pretty straight forward and easy to copy: Essentially everything remains the same besides the the top board which is replaced with a longer one (1,4m), in order to get some sliding range. It's also very important to add stops to each end of the sliding board, to keep your slider - and your camera on top of it for that matter - from sliding off the construction.
I also added some felt patches to one side of the board, to make the ride smooth and quiet.
~ FJ Renard, Berlin
Materials: 1. Pruta (the small rectangular one), 2. a ruler or something to measure, 3. something equal to a credit card in size (i.e. your ikea family card :)), 4. a cutter, 5. pincers, 6. a needel, 7. one raspberryPi
Description: 1) Put your credit-card or similar in to the pruta box; this approximately marks the level where your raspberriPi will go.
2) Make the needle glowing (very hot?), holding it with the pincers, and use it to perforate the plastic as showed in pictures below.
The 4 small holes will serve to hold the corners of your raspberriPi while the big circular hole will room the yellow connector as you can see in picture below.
3) When you have the raspberryPi in place inside pruta box (for this purpose the holes made at step 2 are enough) make holes for others connectors in the same way.
4) If you want something for the eyes print the raspberriPi logo and glue it to the top of pruta box; With the same technique perforate the coloured part of the logo.
Enjoy! :)
~ Andrea Tarocchi, Milan